Actual Wiring Diagram 3. Assembly Procedure 4 Disconnect the connector. Match the center of the mylar in the horizontal direction to the center of the raised part. Place the original that you wish to scan on the Note computer, the “Select Device” screen will open. SIM Machine Not stop.
|Date Added:||9 June 2013|
|File Size:||51.23 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Troubleshooting In addition to this section, troubleshooting information stkdio also be found in the README files for each of the software programs.
Page 62 36 Remove two E-rings and remove the paper feed roller. Use a long scale for precise adjustment. FAX control is terminated. To use this e studio 203sd, open the printer driver setup screen and select studil or “4-Up” for “N-Up Printing” on the “Main” tab. Refer to the figure below. Install the software according to the Operation Manual. Canon Imagerunner Advance Ci.
A uniform negative charge is applied over the OPC drum surface by layer the main charging unit. Toshiba e-studios Spesifications 4 pages. When the e studio 203sd does feed.
Button Manager allows you to configure six sets of scanning settings as a scan 203ds on the machine.
When reassembling, be sure to engage the Duplex motor DG check gear with the belt on the main body e studio 203sd. Match the center of the mylar in the horizontal direction to the center of e studio 203sd raised part.
This feature is used to enable correct printing on envelopes and other paper with flaps that can only stucio loaded in one orientation. If the fusing unit is opened without sliding the fusing lower earth spring, the fusing lower earth spring is deformed. Unpacking 4 Remove the CAUTION tape from the front cover and remove the two protective pins from the fusing machine by pulling the strings upward one at a sthdio.
Don’t have an account? Page 27 4 Select “Connected via the network” and click the “Next” button. E studio 203sd Moving instructions When moving the unit, follow the procedure below. Stick the lower part stduio the cushion to the mylar, too.
Toshiba eStudio Printer 21ppm Multifunction Printer
Indicates the speed from 1st to 30th sheet i. Club Copying is an independent reseller, established The paper is loaded so that printing takes place on the back side of the paper. Align with the raised part the yellow line in the diagram below. Manual Paper Feed Section 1 Remove e studio 203sd screw and remove the multi upper cover. To use the feature, select the image orientation in “Image Orientation” on the “Paper” tab, and then select the “Rotate degrees” The scanner driver setup screen will appear.
E studio 203sd key left key together, and turn on the power simulta- neously. Machine conditions check [Function] CPM When this test command is executed, the current machine setting is displayed.
Remove it and then set the documents again. For e studio 203sd on specifying the scan area and setting To cancel a scanning job after clicking the “Scan” the scan preferences, see scanner driver Help. End digit of year Production place 4. Page 52 8 Move the carriage to the position indicated on the figure.
Assembly Procedure 4 Disconnect the connector.
The Print Status Window is a utility that monitors the machine and shows the name of the document being printed and any error messages that occur. The alphabet following the LF mark shows the kind of lead-free solder. Test chart Test chart 2 Perform the adjustment in each mode. To use this function, open the printer driver setup screen e studio 203sd select “2-Sided Book ” This manual also for: Use care so that the rib on the upper transport release arm catches the guide.
The display is shifted to the sub code e studio 203sd standby menu. To assign a name to a tab, click the “Menu Name” button and enter the desired name.
Replace the developing unit. e studio 203sd
Toshiba e-STUDIO203S Online Manual
e studio 203sd DV doctor Page 68 – B. Only one set of copies Page Attach the E studio 203sd to Marking line. List Part name Ref. Page When the set value is increased, copy becomes darker.
Attach the cushion leaving 3 – 7mm from the edge so that the gap between the Fan housing cushion and the filter of the rear cabinet is filled for sure. Table Of Contents L. Precision Roller is in no way affiliated, sponsored or endorsed by these copyright owners or their affiliates or dealers This website uses a secure server to encrypt all sensitive information.
The function can be disabled.
The use of controls, adjustments or performance of procedures other e studio 203sd those specified herein may result in hazardous radiation exposure. 203s catalogue includes Canon and Toshiba multifunctional printersphotocopiersMFDs, fax machinessmall and home office desktop devices and all related consumables such as toner, drum units and office paper supplies.